|
Price List
GENERAL
|
Complete clean, oil, safety
& function checks |
$35.00 |
|
General repair |
$35.00 per hour, plus cost of parts |
FINISHING (METAL) *
|
Teflon coat rifle, handgun or shotgun |
$140.00 |
|
Cold blue after repairs which damage finish |
N/C |
|
Fine or coarse (satin/matte) glass bead blast |
$65.00 |
|
Metal polish, to 400 grit |
$80.00 |
|
600 grit |
$100.00 |
|
"matchless" (almost mirror) |
$150.00 |
|
Hot blue firearm |
$100.00 |
SIGHT WORK
|
Sight in customer's gun |
$25.00 plus cost of ammo |
|
Drill & tap barrel or receiver for sights or scope mounts |
$15.00 per hole, plus cost of sights or mounts |
|
Mount scope on pre-drilled & tapped gun |
$25.00 plus cost of mounts, rings & scope |
|
|
|
|
New sights on handgun, if no milling required
if milling required |
$35.00 plus cost of sights
$85.00 plus cost of sights
|
GENERAL RIFLE WORK
|
Test fire |
$10, plus cost of ammo |
|
Check headspace |
$25.00 (partial disassembly required) |
|
Check firing pin protrusion |
$10.00 |
|
Remove fired case from chamber |
$35.00 |
|
Mill Remington bolt for Sako/AR15 style extractor |
$100.00 |
|
Remove live round from chamber |
$50.00 |
|
Remove obstruction from bore |
$35.00 |
|
Cut & crown barrel muzzle |
$50.00 |
|
Turn & thread shank of barrel blank, chamber, fit to action |
$150.00 plus cost
of blank |
|
Lap in bolt lugs (does not include setting barrel back) |
$65.00 |
|
Welding on new bolt handle or reshaping current handle |
$65.00 |
|
Triggers (installation or adjustment) |
$45.00 plus cost of trigger (if install) |
HANDGUNS
|
Chamfer revolver forcing cone |
$45.00 |
|
Chamfer revolver chamber
mouths |
$45.00 |
|
Recrown revolver muzzle 11° |
$45.00 |
|
Revolver action job |
$95.00 plus cost
of new rebound spring ($5) |
|
Rebarrel revolver |
$100.00 plus cost of barrel |
|
Straighten revolver crane |
$45.00 |
|
Install ball detent crane lock |
$65.00 |
|
Remove/modify revolver hammer spur |
$50.00 |
|
Tighten slide to frame fit |
$85.00 |
|
Fit barrel to 1911 auto
Non-ramped
Ramped
any
crown on barrel
|
$85.00 plus cost of barrel
$85.00 plus cost of barrel
$45.00 ($20.00 if done with barrel install)
|
|
Fit/install bushing on 1911 auto |
$35.00 (plus cost of bushing) |
|
Bevel magazine well of 1911 auto |
$50.00 |
|
Hand checker front strap (20 or 30
LPI) |
$250.00 |
|
Stipple front strap |
$100.00 |
|
Checker or stipple new blank mainspring housing (1911) |
$50.00 (plus cost of housing) |
|
Serrate rear of slide |
$75.00 |
|
Open & flare ejection port of 1911 slide |
$50.00 |
|
Throat & polish barrel and feed ramp of 1911 |
$45.00 (often
factory barrels need additional reaming; if so, add $25.00) |
|
Re-cut, polish and tension extractor |
$35.00 (plus cost of part if
needed) |
|
New ejector, fit & cut |
$35.00 (plus cost of part) |
|
Fit new trigger to 1911 |
$35.00 |
|
Trigger job on 1911 |
$75.00 (plus cost of parts) |
|
Replace springs for tune-up |
$5.00 (plus cost of spring kit) |
|
Cut frame & install beavertail grip safety |
$125.00 (plus cost of safety & refinish) |
|
Fit new thumb safety |
$45.00 plus cost of safety |
|
Machine forward cocking serrations |
$100.00 |
|
"Melt" package, deburr and radius all sharp edges
(will require extensive refinish) |
$55.00 to $100.00
(depending on degree of dehorning requested) |
STOCK WORK
|
Hand rubbed oil finish |
$135.00 |
|
Spray-on for synthetic stocks |
$35.00 |
|
Recut checkering |
$45.00 per hour |
|
Glass bed barrel and/or action |
$75.00 |
|
Pillar bed |
$75.00 |
|
Install recoil pad |
$75.00 (plus cost of pad) |
|
Install sling swivels |
$35.00 |
|
Inlet and finish semi-finished wood stock blank (does not include
checkering, recoil pad, grip cap, forend tip, sling swivels or other
attachments) |
$250.00 |
|
Fit, bed and finish fiberglass stock blank |
$200.00 |
|
Fit & install prefinished synthetic stock |
$50.00 (plus cost of stock) |
|
Camo paint synthetic stock |
$75.00 |
|
Checker forend and grip of wood stock |
$300.00 |
(Prices subject to change without notice -- often due to supplier price
change)
SOME COMMENTS AND THOUGHTS:
Although I offer general gunsmithing and repair, it might be
helpful to know that I specialize in the following:
RIFLES:
Bolt action
AR-15 types
Ruger 10-22s
AK
variants
HANDGUNS:
1911 styles
Browning Highpowers
Glocks
Smith & Wesson revolvers
On these listed firearms, I can offer my customer anything from a simple
tuneup to a complete rebuild.
1911 auto work is not limited to the basics listed. I can build you a
carry gun from the ground up, or offer "package deals" on your guns.
I am happy to sit down and talk with you about what you want from your 1911.
Any oddball, unlisted or miscellaneous work will usually be $35.00 per hour
plus parts.
Please do not ask me to deactivate any safeties. I won't. Any gun found to
have a non-functioning safety will be repaired to functioning condition, and the
customer charged. Sorry, but this is non-negotiable.
The only exceptions are removing the magazine safety from the Browning
Hi-Power during a trigger job and removal of Colt or Para Series 80 parts.
These will be done at the customer's signed
request and waiver.
Please don't ask for a rush job. I would rather be known for the quality of
my work than the speed.
When it comes to custom work I prefer to work with the best aftermarket parts
available. With general repair we can be fine with OEM parts, but if you want a custom gun to be proud of, I won’t cut costs on parts.
I keep OEM take-off parts as part of my fee unless otherwise specified.
Disclaimer:
I will do no work on any firearm that
has been modified to render it "illegal" under current firearms laws,
unless it is to return the firearm to legal condition.
Under the terms of my license I will be obligated to report such a firearm to
the ATF (unless the request is to return it to legal condition).
|
